Is your company following OSHA fall protection standards?

The Occupational Safety and Health Administration (OSHA) has determined that the four most significant causes of death and injuries in the construction industry are caused by falls, electrocutions, caught-by, and struck-by incidents. The first two are self-explanatory. Being crushed by the moving outrigger on a man lift is an example of a caught-by accident. Being hit by an excavator’s bucket as it slews or an unstable stack of lumber is a struck-by accident.

According to the Bureau of Labor Statistics, in 2012, the majority of contractors (54 percent) were working in construction and extraction occupations when fatally injured. The deceased in this occupational group were most often employed as construction laborers (101), first-line supervisors of construction trades and extraction workers (42), electricians (39), and roofers (32). For more information on fatal injuries incurred by contract workers, see the 2012 charts.

Falls in residential construction

Those who are not already on board with safety practices should ask themselves why? Based on injury records on falls from attics or between ceiling joists, OSHA has established enhanced residential fall protection standards. If truss chords or ceiling joists have insufficient structural integrity to bear the load of one or more 150- to 200-pound workers, plus their tools and materials, the truss of joist system may collapse dropping workers 8 feet or more and possibly landing on others working in the space below.

The system must be inspected before work begins. A temporary wall might be installed or employees should work between the ceiling joists from a scaffold. Plywood decking on the joists or truss chords may also make the structure safer.

What is fall protection?

Fall protection involves equipment and techniques designed to prevent falls and or reduce injury if a fall takes place.

Let’s first talk about equipment.

Equipment must be chosen, installed, used and maintained properly for the conditions in effect, and be assembled properly under the supervision of a competent and qualified person.

A manlift must be stabilized when elevated and workers must be careful of ejection from a bucket when motorized lifts moves over uneven ground. Railings and anchorages must be in good condition and must be properly rated for the relevant loads and hazards.

Ladders must be properly rated, footed on a stable surface, in good condition and the top at 3 feet above the parapet for safe access to a higher level.

Scaffold components and all hardware must be properly integrated and in good working order and outriggers used if necessary. Planks must be in in good condition, without improper holes.

Guardrails need to be stable, mounted to solid anchorages, 42 inches high, with proper midrails, and able to withstand a 200-pound force.

A full-body harness distributes the forces throughout the body, and the shock-absorbing lanyard decreases the total fall arresting forces.

A full-body harness distributes the forces throughout the body, and the shock-absorbing lanyard decreases the total fall arresting forces-OSHA

Fall restraint systems pay out line to allow a person to work safely at the ledge, but stop upon a sudden load to prevent or stop a fall. It is somewhat like the line and leash on a dog run.

A warning line system is comprised of ropes, wires or chains that serve as a strong reminder to stay (depending on the work) not less than 6 or 10 feet from a ledge.

What fall protection is required?

OSHA requires the proper use of safe, properly rated and installed ladders, scaffolds and a personal fall arrest system (PFAS) for workers in attics and all work at 6 feet or greater above interior or exterior surfaces. These hazardous locations are not limited to attics and roofs, but include the high exterior decks or patios and the walls or ceiling in a great room.

In its recent residential fall protection advisory, OSHA recommended the use of a pre-installed anchorage system, a cable in the attic to which the worker would clip his/her safety lanyard when entering the attic or other elevated work space.

While we are not required to use fall protection equipment while performing initial inspections and evaluations of conditions in a remodeling project, we must obviously still exercise extreme caution and good judgment before entering precarious, confined or otherwise potentially unsafe conditions.

A PFAS is designed to safely stop a fall before the worker strikes a lower level. It includes three major components:

  1. An anchorage to which the other components of the PFAS are rigged.
  2. A full body harness worn by the worker.
  3. A connector, such as a lanyard or lifeline, linking the harness to the anchorage. A rip-stitch lanyard, or deceleration device, is an essential part of the system.

Once these systems and procedures are in place, the employer’s safety culture and worker training must come into play. Each worker needs to know how to properly use the equipment and be expected to report an unsafe condition, damaged equipment shall be taken out of service and repaired if possible—or discarded—and safe practices take priority over expediency.

Training and implementationImagesforPowerPointPresentation040

Ask yourself:

  • When was the last time you used a 2 x 10 as a scaffolding plank?
  • What is the proper loading on that pick board?
  • Does the scaffold need outriggers?
  • Is that lanyard connected at a secure anchorage?
  • Does the system require toe boards? What is a toe board?
  • What safety rules apply on a multiple-contractor site?
  • Who is your OSHA-approved competent person and what are that person’s duties?
  • How do I create and implement a safety plan?

If you do not know the answers to these questions, you have a duty to take an OSHA 30 for Construction class and get your team into an OSHA 10- or 30-Hour class. Otherwise, you, your team, your business and your client are at risk. The same is true for your subcontractors.

In any case, all projects need a safety plan, which must include fall protection. While employers are concerned about OSHA catching and fining them for a violation, our work is not primarily about OSHA. It is about your employees performing high-quality remodeling work and going home uninjured at the end of the day. In many cases, your company is literally family. Working safely takes a little time and money, but what are the potential savings in case of an accident in lives, injuries, illnesses, careers, time, productivity, stress, money, your business, and your client?—Wayne Baruch, MBA

Additional resources

Browse www.osha.gov and either enter “fall protection” or other search parameters in the “Search” window or click on “A to Z Index”.

Ten- and 30- hour training is available from a number of OSHA authorized outreach training centers and online. Online training may be less expensive and more convenient, but not all people learn as well in self-directed as they do in classroom training. In addition, your instructor may be able to customize your experience with electives and options to better match the risks in your work.

Wayne Baruch, MBA, is owner of The Artisans Group and expert witness/consulting practice in Hillsborough N.J. and is an OSHA-authorized outreach trainer.

| 5/12/2014 12:00:00 AM | 52 comments
Add Blogs to RSS FeedAdd Blogs to RSS Feed

Recent posts

No recent posts

Post archive

May 2022(1)
April 2022(2)
March 2022(3)
February 2022(1)
January 2022(5)
October 2021(2)
August 2021(3)
July 2021(1)
June 2021(2)
May 2021(1)
March 2021(2)
February 2021(1)
December 2020(1)
November 2020(2)
October 2020(2)
September 2020(3)
July 2020(3)
May 2020(2)
March 2020(2)
January 2020(2)
November 2019(1)
October 2019(4)
September 2019(3)
August 2019(3)
July 2019(5)
June 2019(3)
May 2019(5)
February 2019(3)
January 2019(3)
December 2018(1)
November 2018(3)
October 2018(2)
September 2018(3)
August 2018(3)
July 2018(4)
June 2018(6)
May 2018(3)
April 2018(2)
March 2018(3)
February 2018(1)
January 2018(1)
November 2017(4)
October 2017(5)
September 2017(6)
August 2017(4)
July 2017(2)
June 2017(2)
May 2017(4)
April 2017(6)
March 2017(3)
February 2017(6)
January 2017(6)
December 2016(3)
November 2016(4)
October 2016(8)
September 2016(5)
August 2016(3)
June 2016(3)
May 2016(5)
April 2016(4)
March 2016(5)
February 2016(4)
January 2016(4)
December 2015(3)
November 2015(4)
October 2015(9)
August 2015(4)
July 2015(3)
June 2015(7)
May 2015(2)
April 2015(5)
March 2015(9)
February 2015(6)
January 2015(7)
December 2014(2)
November 2014(7)
October 2014(5)
September 2014(3)
August 2014(5)
July 2014(6)
June 2014(7)
May 2014(3)
April 2014(5)
March 2014(8)
February 2014(7)
January 2014(7)
December 2013(6)
November 2013(8)
October 2013(5)
September 2013(4)
August 2013(4)
July 2013(6)
June 2013(8)
May 2013(8)
April 2013(15)
March 2013(6)
February 2013(11)
January 2013(8)
December 2012(6)
November 2012(7)
October 2012(20)
September 2012(14)
August 2012(6)
March 2012(4)
January 2012(1)
April 2011(2)